Hey! Old Man! It Ain't 1960 Anymore

So much of the knowledge most of us have picked up at the range, hangin' out out the gun store, bullshittin' online has been passed down from generation to generation. The grizzled old hunter is full of tales of prowess with that most American of tools: The Rifle.

Now, these oldsters have lived through the fanfare, frenzy, and hype of the introduction of many a hot-shit new cartridge. Some have even tried a thing or two. Some made legends whose name not only lives on the cartridges they pioneered but is applied to cartridges modified in similar fashion 50 years later. Most watched from the sidelines while other brave souls reached for the brass ring of better, faster, more accurate, more effective, more destructive perfection.

Listen to the Old Men who are still around to tell tales of deeds done and daring do, but do not fail to leaven that download at the first available opportunity to insure it still pertains to the rifles and cartridges bearing the improvements in applied technology available to us today. In many ways there is nothing new under the sun, in other ways what was once so is so no more.

We have all heard of the 220 swift burning the throats out guns it was chambered in, of the impossibility of spinning a long small caliber bullet hard enough to stabilize without having it disintegrate as it exits the barrel, how "Old Slab Sides" (1911 model pistol )is inherently inaccurate and those new .40's have bullets so short they tumble, those plastic guns just don't hold up.

Now that 220 will still self destruct with heavy use of hot loads, but the rest of that stuff is pure steamin' bull shit. Feel free to call call 'em on it.

Case in point; Those fast calibers spinning themselves apart:

These bullets are all running over 4000 feet per second, some over 4400. Thats Mach 4 people.



Hey! Old Man! It ain't 1960 anymore!

If Where the Red Fern Grows makes you sad....

You should see this.

Ingenious Execution: The Kel-tec SU-16

First of all, I have to give credit where credit is due: Nathan had nothing whatsoever to do with discovering or researching this rifle.

Now that's out of the way, let's take a look at what we have here:

The Kel-tec SU-16 is a gas operated semi-automatic rifle chambered for the 5.56mm NATO. It blends an AR-15 type locking bolt, the ability to use AR-15/M16 milspec magazines, an under-folder stock, integral bipod, and receiver mounted picitinny rail, with a clean operating AK47 type gas operating system. This rifle comes in 6 variants "A" - 18 inch barrel, "B" - Shorty "A" model, "C" - Threaded barrel and the only model that will fire with the stock folded, "CA" - Legal in , "D" - Short barreled rifle and NFA regulated, and PLR-16 - Pistol version. The variant we are concerned with here is the "C" model. The attraction being the threaded barrel and the ability to fire folded.


Y'all can look up and ponder the many and various features of this particular rifle on your own time. Suffice it to say it has the potential to be and Interesting Gun. That potential is only realized if the rifle in question is accurate, for as none other than Col. Townsend Whelen himself said, "Only accurate guns are interesting".

We shall see...




I removed the rifle from the box, unfolded the stock, deployed the bipod and began the task of familiarizing myself with its operation. "Break Free" oil was applied anywhere I could get a wear indication or scuff to show itself after working the various mechanisms by hand. The receiver of this gun is some sort of plastic and normally these types of weapon benefit more from graphite grease for lubricant than oil, but it remained to be seen how dirty this rifle operated so I stuck with the light oil for now.

Normally, I consider range testing a waste of time with open sights, especially in a high velocity caliber, so I grabbed the scope off the .454 (pay attention, you willl see this again) and pressed it into service with a set of see-thru rings onto the SU-16's receiver mounted picitinny rail. I bore sighted it the old fashioned way, loaded up, and headed for the range.

Procedure:
I like to observe both the accuracy of a rifle and it precision while sighting it in. I fire into a 25 yd target, adjusting to the desired point of aim in small increments. Yeah I see the flyer. It was colder'n a witches titty in... well, in....January.

On to a 50yd target. I like to shoot pairs and tripets within about five seconds of each other as I make adjustments, cooling the barrel between the strings. Sure, it can be done with single shots, but you can't observe the effect of a quick cold to hot barrel temperature transition and it's effect on point of impact. The SU-16 is impressive so far.

I had been noticing the reticle on the long eye relief pistol scope seemed to be rotating clockwise ever so slightly, so I dug out the allen wrench and snugged everything up. I figured given the shitty weather I would stick with the slight rotation and finish up at least able to measure a 100 yd group even though point of impact was screwed.

I loaded the ten round clip to capacity and began work on the 100 yd target. Somewhere around the third round I could see the reticle was rotating further so I went on and finished the magazine to at least complete a feed function test. You can see the string of holes running up the left side of the target as the reticle gave out completely. This is the third scope which has fell victim to the .454 Casull. Shit.



I hated to leave without some 100 yd results so I said "WTF" and pulled the scope and ran a boresnake down the barrel. I loaded three rounds, settled in behind the gun, squinted my old eyes, settled my breathing, slowed my heart, my focus narrowed to that tiny little needle Kel-tec placed on top of the front sight post of this rig. As the rest of the world fell away I began squeezing tighter and tighter.... The result:


The gun mags and most others figure that's a .75 inch (3/4") group reporting the range of error from the center of the group. I call that a 1.5 inch group since I'm not lookin' to sell any guns for advertisers and it's always best to report what you measure, not what you figure, whenever possible. Keeps things clearer, and it never hurts in the gun store or at the range to under-report your results. Makes it easier to beat a fella out of a cold brew.

Conclusion:
Kel-tec has done with the SU-16 what folks expected from Ruger with it's mini-14 POS. I'll hear no more small diameter barrel excuses for the Ruger. They are makin' shit and sellin' it for shinola. Hell this little honey even has the boys over at AR15.COM diggin' their panties out of their ass crack.
Kel-tec's attention to detail, proven technology design, and innovation have yielded
an Interesting Gun.

Throughout this test no malfunction whatsoever appeared. This is important because though only accurate guns are interesting, only reliable guns are worth keeping. I think Colonel Whelen would approve.

****Look Here Y'all****
I did not post this as an invitation to mini-14 bashing, even though I did start it. A lot of folks bought them with high hopes when they were the only game in town and are suffering for it, no sense in beatin' them up.

The SU-16 is being criticized at AR15.com because it has an activation rod (a la AK47). Never mind that the AK is the standard for reliability the world over.....